Water heaters are the kind of appliances that just stay in the corner, comfortably doing their job. And suddenly one morning you see it pooling the basement, making peculiar sounds and breaking down. It can be leaking water from the tanks or inconsistent water temperature. If you witness any of these problems then your first job is to get a new water heater as soon as possible. But if you want water heater repair, San Diegothen you should go for it.
Installing a water heater has become very costly nowadays. Someone professional can charge you more than 700-1000$ and additional costs are gas burning and more than fifty gallons of water. When the winter is coming, warm water becomes a necessity, and the charges for replacing a water heater with a new one can cost a big hole in your pocket.
Here, we are going to discuss a simple but complete guide on how to install a water heater on your own and save some of your hard-earned money.
Here are a few things you are going to need While doing the installing:
- Tools: Screwdriver, adjustable wrenches, electrical tape, tube cutter, plumber tape, etc.
- Parts: A new water heater, pipe fittings, small pieces of pipe, and valves.
- Supplies: Towel and leak check solutions, buckets, water heater drain pan.
First, let’s install New Water Heater: Installing a new water heater is not as difficult as it seems. We just need to follow a few simple steps. And with that, a new water heater will be installed without burning some extra cash out of your pocket. But first, you need to make sure that you require to install a new one. If the condition is not that bad, repairing the whole system can be a good option. You can contact Top Water Heater Repair Orange County to solve the problem. But if you can’t find it anyway, then here I am mentioning a few simple steps that you need to follow:
- Set The New Water Heater in the right place: First decide the place where you want to keep your water heater. Put the new heater in a drain pan for now. You can choose to avoid flooding by simply connecting the drain pan to the main drain of your house.
- Now Install The T&V valve: T&V valve is needed for safety. If the temperature or pressure inside the heater reaches very high then the valve will automatically open up. If your heater doesn’t have them pre installed then buy them separately and install them.
- Install the discharge pipe: make sure the position of the discharge pipe should be towards the floor and attached to the T&P valve. Water will come dripping from the pipe so make sure you have a drain or a bucket underneath the pipe.
- Hook up the water lines: Hook up the cold water line. Hook up the hot water line. Use flexible hose kits for hookup. Apply plumbers tape to the threads of the heat trap nipples. Then attach the hoses.
- Now Install And Secure the fittings: Some areas of the heater need dielectric fittings which will help to reduce the corrosion between two different metals. Now add the plumber tape to the connector of the body threads. Then Secure the fitting to the hose. After that, you need to hold the hose up to the pipe.
- Now it is time to secure the compressor nuts and rings onto the pipe. After that, tighten it.
- Time to fill the tank: Now you slowly turn on the water supplies and check every connection to be confident that there is no leakage. After the confirmation of zero leakage, fill the water tank. If any leakage appears, just pause the water supply and tighten the connection. Repeat this process until you see no leakage.
- Now flush the tank: When the water starts running from the faucet, the tank is full. Then flush it so that any air or debris present in the tank, comes out.
- Connect the power source: Attach the ground wire to the green ground screw. Use masking tape and twist the end of the wires with wire connectors.
- Now turn the power on and set the desired temperature: Follow the manufacturer’s instructions to set the temperature. At first, It can take a few hours to heat the water.
As your water starts heating up and the pressure is stabilized, some leakages can still reveal themselves. Fix all of them and get ready to have an amazing shower.
What to do if water is leaking from the heater:
Water leakage can happen in a water heater due to several reasons. Which includes loose valves, excessive pressure in the tanks, or the pipes or pipes that connect the units. It is better to call a plumber then. Or, you can contact top Water Heater Repair Orange County for the best service. Better you should turn off the power supply of your leaking water heater and shut off the water pressure of the tank.
New heaters can also leave water under them but it is not because of any leakage. This is because there is an insulated lining between the tank and the outer shell which gathers humidity while it is in the storage. Now when they are being heated up for the first couple of times, the trapped moisture condensates. It runs towards the bottom and onto the floor. There is nothing to be concerned about. It’ll be alright in the next couple of days.
Before finishing, Here I am mentioning some additional things that you may need with a new water heater. They are:
- Since a water heater nearly consumes 17% of total power usage, you’ll be needing building permissions.
- A dedicated shutoff valve that lets you shut off water to the water heater in case of repair and maintenance so that the water supply of the rest of the house doesn’t hamper.
Depending on the type of water heater, a typical heater lasts around 10 to 15 years. Regular water heater maintenance heavily affects the life expectancy of a water heater. Hopefully, the information will help you.
Author Bio:
Aimee is a marketing manager at EZ Plumbing & Restoration. She is very passionate in writing about discrete plumbing services and leakage detection as well as repair solutions.
